Engine Masters

Do boost leaks really even matter? Can vacuum leaks make more power? You read those questions right. Come be surprised right along with us as we find power in unexpected places, and lose less than we'd expect in others.

With the power potential of E85 available only at limited gas stations, having the ability to run a blend of gasoline and E85 in your street car is a game changer. Credit the flex fuel sensor. By sampling your fuel composition and adjusting fuel flow, you can not only run a mix of fuels, but make more and more power as you mix in more and more E85.

It's arguably the coolest carb configuration of all time. The 3x2 setup on the six pack was designed to supply part-throttle economy on the center carb while the outside carbs kick in for power! The guys shoot out three of the coolest vintage six pack designs to find out which is gimmick, which is greatness, and which makes the most power on a street 440.

What do you do when your 800-horsepower 572 just won't get you consistent eight-second passes in your '31 Model A? Well, if you're David Freiburger, you strap it to the Westech dyno to tune, poke and swap at until you're at a comfortable 950+ horsepower.

We all know oil pressure is critical. Not enough can leave you broken, and too much can have you springing leaks. But can too much also be robbing precious horsepower? To find out, the guys test three commonly ordered LS oil pumps in different volume and pressure configurations to see if oil pumps can in fact be enough of a rotational drag to affect power production.

Same test, new twist. We've tested single V-split pattern cams before on Engine Masters and concluded that a split pattern can increase top-end power without necessarily affecting bottom-end torque. Well, our findings have been challenged, and we're here for the science.

This test is all about choosing the features you want and need on your carburetor, and how those features affect horsepower and tunability. Do mechanical secondaries really make any more power than vacuum-power ones? Does a choke horn restrict inlet airflow?

No matter how many LS swaps are out there, the old-school SBC is still an absolute force in the marketplace. On this episode of Engine Masters, the guys bolt three of the lowest-buck cylinder heads out there to their Ultimate Average 383 and make pulls for power!

How much hidden power is lurking in your existing engine combination? We're here to show you how to find it without buying, changing or upgrading a single component. We use all the little tips and tricks we've learned over the seasons to super-tune every bit of remaining horsepower out of the 410ci Windsor from David's Disgustang.

You've seen them around for years, you may have considered running them, you may even have them on your car right now. But do exhaust cutouts really serve any purpose beyond rattling the drums out of passersby’s ears? Well, proponents have always claimed they make your car faster, but on this episode of Engine Masters, presented by AMSOIL, we see how they stack up against a full exhaust and a header extension behind our heavy-breathing 598-cubic-inch Big Block Chevy. We run them in multiple positions as well as both open and corked to see just what effect they have on power, no matter how you want to run them.

For all the folks out there opting to run a carburetor on the new-fangled LS, we have six different manifolds to sandwich between our old-school carb and our new-school 6.0 LS. We not only show you the differences between these popular manifolds, but also how to get your LS running with a carb as easily as possible.

So you've got an LS and you need to make a choice on an intake. Chances are high you're looking at some version of Holly's "Ram" Intakes, whether it's the long runner Hi-Ram, the Mid-Rise, the compact Lo-Ram, or the hood-clearance-friendly Ultra Lo-Ram. On this episode of Engine Masters, presented by AMSOIL, we line them up one by one on our 550 rectangle port headed 6.2-liter LS to help you decide which power curve is best for you. But fear not, cathedral-headed LSers, this test applies for you, too!

You've seen them all over. On vintage race cars, trophy trucks, motorcycles, and even—for some reason—street cars. They're header wraps, and manufacturers claim they not only reduce radiant heat, but create additional power through their scavenging effects and superior heat management. Is any of it true?? We'll find out on this episode of Engine Masters, presented by AMSOIL, as we test a set of painted, ceramic-coated, and wrapped headers against one another on our Ultimate Average 383.

The Mopar Max Wedge head was once considered all but unobtanium. The aftermarket has finally come to the rescue, making Max Wedge heads that are both available and affordable. On this episode of Engine Masters, presented by AMSOIL, we've got an example of a 270cc Trick Flow unit to see if the Max Wedge style, with its bigger intake runners and more direct flow path, are really a worthwhile upgrade for YOUR typical street/strip big-block.

One fuel, two fuel, hot fuel, cool fuel. If you think that was a mouthful, just wait until you hear what our guys have to say in this one! Inspired by the learnings from Episode 43’s study on coolant temperature testing, we're going one step beyond icing down the manifold. This time on Engine Masters, presented by AMSOIL, we're deliberately heating and cooling our fuel to see the difference it makes to the tune and the power output of our Ultimate Average 383.

Are your cast manifolds enough to keep up with your turbo motor? And at what point should you be running proper headers? Those are the questions we're asking this time on Engine Masters, presented by AMSOIL. Using a typical mill you'd find in a turbo street car, we're running our 630-hp 5.3 LS with factory exhaust manifolds and again with turbo headers to show you the differences in boost, backpressure, and horsepower.

It's the age-old battle of power v price, but is it as simple as all that? Are you really giving up significant power by cheaping out on a solid flat tappet, or is the extra power of the roller worth every penny? Join us on this episode of Engine Masters presented by AMSOIL as we talk duration, lobe intensity, spring pressures, dollars and horsepower.

The Windsor family finally gets its turn at an intake shootout! The test mule is a Dart-based Windsor, and it's just begging for the best single-plane manifold to breathe through. With offerings from Edelbrock, Trick Flow, Ford Racing, AFR and SpeedMaster, we're sure to make our small Ford sing!

We're battling two iterations of the 5.7 Gen III Hemi, the '03-08 vs. the '09-current, and we're learning a TON in the process. With an eye toward engine-swap simplicity, we've stuffed them both with the biggest cams they can handle and managed fuel and spark in the most affordable way possible for each

A debate has raged in the LS community for years about the difference in power potential between dime-a-dozen cathedral ports and the "racier" rectangular ports found on the LS3. The rectangles have bigger intake ports, flow numbers, valves and chambers, but what does it all add up to?

Driven by lunacy as much as novelty, Dulcich is at it again with his slant-six tomfoolery. With goals of his 225ci monster powering a daily driver '68 Dart, Steve is putting four aftermarket intake manifolds to the test to see which will give him the most grunt.

The Holley 4150 has been the gold standard for performance since it was released to the aftermarket in the '60s. Seemingly everyone has one, but do you really know how to tune it? Resident carb whisperer Steve Brule walks through all the tips and tricks you need to know to get your 4150 running its best on any engine.

We explore the differences between single and split-duration camshafts. Can the extended exhaust duration of the split pattern crutch poor exhaust flow? Does the single pattern really suffer at RPM in the name of low-speed torque? And why would you ever not want to run a split pattern?

We dive into the fundamentals of the cheapest, easiest and most effective way to give your motor some grunt: nitrous oxide. Using the most basic 150-horse plate system, we'll show you the basics on installation, safety and tuning for nitrous on your typical carbureted engine.

We've done air filter shootouts before, but none like this. On this episode of Engine Masters, it's all about finding the least restrictive way to route a cold air system. We're here to find out how much the size of that filter, as well as the length, path and diameter of the tubing, affects your performance.

The guys explore the cooling benefits of water-methanol injection. They'll be looking at any added tolerance to detonation, intake air temps, how much to inject at what rpm, and the optimal ratio of water to methanol. There's plenty to explore with a little experimentation on the dyno.

The guys study the fueling demands, horsepower, and the pros and cons of running 116 octane gasoline, E85, methanol and oxygenated gas. They all have different oxygen contents, air/fuel ratio demands, and ultimately, different abilities to cool the cylinder and create power. What does that all mean, and which is right for you?

You've seen them, you've drooled over them, and you may have even run them. We dive into the wavy waters of individual runner systems, how you can tune them, and whether all that cool makes any more power than the stalwart carburetor.

We love our big-block Mopars here at Engine Masters, and we've finally put together a horsepower-per-dollar comparison of street-centric wedge cylinder heads. Want to spend bottom dollar on some 906s? We've got you covered. Want to step all the way up to CNC-ported, tall-valve set of TFSes? Tested.

We all know that adding any sort of restrictor -- like a muffler -- is going to hurt power on a turbo motor. We also know that sometimes it just makes sanity-sense to cut down excess noise. The crew tries to find out just how much horsepower that sanity costs.

Sounds boring, we know. But if you're like us, you've always chosen an oil pump based on some knee-jerk instinct. It's time to finally learn the difference between standard, high-volume and high-pressure oil pumps in terms of pressure, flow and horsepower. Come see what there is to know on this episode of Engine Masters.

We're taking trips to the moon as we test different combos on a 331ci small Chevy. Starting with an excellent little combo good for 7K RPM, we step it up to show you how improved airflow on a small motor equals pure RPM. Best of all, we do it all with simple parts and a small budget.

It's a battle between the iconic 440 Six Pack and the legendary 426 Hemi, and we're settling age-old bets on this one. Do they live up to lore of 440 grunt and 426 top end? Can the Six Pack cool outgun the famed Hemi heads?

Does compression make power? The easy answer is yes, but the answers we're looking for today have more to do with how it makes power and how sensitive it becomes to temperature on pump gas. Does it favor top or bottom-end power, or does a point of compression equal a linear increase across the powerband?

Holley carbs have been known for years as the standard by which all racing carbs are measured, but today's question is this: CFMs being equal, is there any difference in power between the smaller-bore, narrower-set "street" style 4150 carb and the bigger-bore, wider-base 4500 series Dominator carb?

When it comes right down to it, nothing that happens on the dyno matters until you get the engine in the car. Today on Engine Masters, the guys test everything that will be used in David Freiburger's Model A drag car.

Does port matching an intake manifold create enough power to justify the cost? On Engine Masters, the crew is going to find out with an out-of-the-box Super Victor, a port-matched Super Victor and an off-shelf Wilson-prepped version.

The crew is on the hunt for two things. First, they're searching for low air temps and big HP numbers as they compare the heat-extracting power of under-roots intercoolers vs. E85! And secondly, they aim to bring up the entire curve by swapping the short-runner blower manifold for a tunnel ram.

Since the dawn of supercharging, compressed air has been stuffed through carburetors, and it's as true now as it was back then. The question today on Engine Masters, presented by AMSOIL, is: what type of carb hat is best for that blow-through application?

As unsexy as it is, protecting an engine starts with the oil and filter. On Engine Masters, presented by AMSOIL, the crew tests 10 different filters back-to-back-to-back. From the cheapest to the trickest in the catalog, they're on the hunt for the best.

The guys find out if mandrel-bent exhaust pipes really make more power over the crimped and crunched pipes the local shop bends up. They test them with mufflers, without mufflers, with turbo mufflers and more on Engine Masters.

On Engine Masters, presented by AMSOIL, the guys put a Demon 650 blow-through carb up against Holley's new Super Sniper Stealth throttle-body-style EFI to see which reigns supreme in terms of tunability, cylinder-to-cylinder distribution and horsepower.

The guys run tests with 87, 91, 110, 116 and even E85 to see if higher octane makes more power, and if an engine's optimal timing even changes with different octane. See what happens as we pump up the gas on Engine Masters.

On Engine Masters, presented by AMSOIL, the crew dives into how cylinder head flow and boost affect horsepower. They run their 363 Windsor once with 195cc and 225cc heads, and declare once and for all if cylinder heads actually matter under boost.

So you wanna street-drive your 1,000 HP monster. You'll need a muffler for the street that will also wring every horsepower possible at the strip. The guys see which street-worthy muffler does the trick on Engine Masters, Presented by AMSOIL.

It's another battle of old-school cool here on Engine Masters, presented by AMSOIL, where the guys bolt tunnel-ram and cross-ram setups to the 383 Chevy and stagger jets until their gasoline-soaked hearts are content.

The common knowledge is that a boosted motor acts just like an oversized version of the NA motor. On Engine Masters, presented by AMSOIL, the guys see if the headers that made the most NA power hold up on a power-boosted motor.

Everybody knows that a lighter car is a faster car. On this episode of Engine Masters, presented by AMSOIL, the guys see if choosing lightweight parts for the rotating assembly helps the engine make more power, too.

Whether they’re Zoomies, Lakes, Tri-Ys, or Fenderwell headers, some pipes are just gotta-haves. On this episode of Engine Masters, presented by AMSOIL, The crew investigates just how much power gets sacrificed in that quest for cool!

Engine Masters, presented by AMSOIL, follows the build of Freiburger's 582ci BBC in his quest for 1,000 NA horsepower. An in-depth rundown of the parts that came together and why they were chosen shows the evolution of the build and the path to glory.

The guys from Engine Masters, presented by AMSOIL, fit the COVID-350 with progressively shorter header collectors to see the effect of a little more piping. Power is just waiting to be collected with some cheap and effective trial-and-error tuning.

On Engine Masters, presented by AMSOIL, the crew answers the high-voltage question of whether upgrading an ignition system is worth it. They load up a big-block Ford with junky leftover parts and replace them one-by-one to see how valuable each piece is.

On this episode of Engine Masters, presented by AMSOIL, the guys guide you through the basics of bringing your motor to the dyno cell for the first time, including motor setup, how the dyno works and how to make the most of your money, time and motor.

You've seen the treasured motorhome 440 before, but not like this! We explore the myriad gains you can find on a sickly, pathetic, low-compression 440 in three stages: first, by plumbing up a turbo; then with a set of too-trick-for-this-engine TFS cylinder heads; and finally with some turbo boost pushing through those heads.

On this episode of Engine Masters, presented by AMSOIL, we dive into one of the most commonly confusing elements of camshaft design: lobe separation angle. A cam's LSA dictates how far apart valve events are, how the engine will idle, where the peak power will live and where the rpm range ends.

1,500 horsepower!!! Need we say more?! We take 555 BBC and the Blower Shop then test the difference in power between gas and e85, and how much more we can make when running each on nitrous.

Ford fans, listen up! It’s your turn to get schooled in the art of intake manifold selection. On this episode of Engine Masters, presented by AMSOIL, we’ve rounded up four of the most popular street-style, dual-plane intake manifolds on the market and strapped them to our test mule. Today, that engine is a something you’d find under many a Ford hood: a 351 Windsor with a stock bottom end, roller cam, about 430 horsepower, and an appetite for more! Oh, and Mustang fans, come find out how much power that hood clearance issue really costs you. You’re not going to like it.

On this episode of Engine Masters, presented by AMSOIL, we put more power claims to the test! This time it's the belief that a simple swap of the standard 1-8-4-3-6-5-7-2 firing order can create more power in your 90-degree V-8. Whether it's changes in manifold pulsing patterns or crankshaft harmonics that make more power, the theories abound. So we're here to do a 4/7 swap on a big 572 to see if there's more power to be had or if the theories are just that: theories.

This time on Engine Masters, presented by AMSOIL, we deliver on a question that fans have been asking for years: “Will a carb spacer make me more power?” The answer is yes, no, and maybe. It all depends on your engine and manifold combination. So come see what works, what doesn't, and how you might be able to get a couple extra ponies for some seriously minimal effort.

Once again, ladies and gentlemen, you asked and we delivered! The question was simple yet timeless: "Which makes more power, a dual 2.5-inch or a single 3.0-inch exhaust system?" To find out, we're swapping pipes on our run-of-the-mill 351 Ford, which makes about 400 hp, and to richen the pot we're also testing out turbo vs. straight-through mufflers and Y-pipe vs. a 90-degree merge. Come get all the data you can handle, right here on Engine Masters, presented by AMSOIL.

Got a solid cam? Well, have we got some free ponies for you! By experimenting with your lash adjustments, you can effectively tune a bit of duration and lift into or out of your camshaft. Looser lash creates a hair less of each; a tighter lash, on the other hand, can actually buy you a bit. Given your specific engine and cam combo, there may be some serious (and FREE!) power just waiting to be tuned in. Come see how to find it on this episode of Engine Masters, presented by Amsoil.

Changing the installed centerline of your camshaft will create a shift in when your valves open and close. On this episode of Engine Masters, presented by AMSOIL, we explore how a little advance or a little retard in cam timing can help you tune your power curve for the high-end performance or low-end power that you’re after.

All else equal, which will make more power, an iron head or an aluminum one? That’s what we’re testing on this week’s Engine Masters, presented by AMSOIL. Aside from the obvious weight savings, there are some real things to consider. Does aluminum’s ability to shed heat help it make more power, or does the iron head’s heat retention promote cylinder pressure and therefore more power? There’s only one way to find out, and that’s right here on the dyno.

On this episode of Engine Masters presented by Amsoil, David and the Steves flip things upside down to find out how much power you might be leaving in your oil pan. Pan shape, windage, and oil control features all play a part in minimizing turbulence around the crank, but is a $1,100 oil pan really worth the cost? Come find out as we test and tune our way to some pretty impressive results.

On this episode of Engine Masters presented by AMSOIL, we found out which cheap carbs produce the most expensive results! We pick a fight between three remanufactured offerings from Edelbrock, Summit, and Demon to see which of these 750cfm bargains will pump the most power into our tried-and-true, Ultimate Average 383 Chevrolet.

Finally, after all these episodes, the Engine Masters crew set out to test the effects of running long rods versus short rods on otherwise identical engines. Do longer rods make more torque? Does the faster swipe past TDC of the shorter rods make all the difference? Or does it not actually matter in the least? We found out, and now you can too, on this episode of Engine Masters presented by AMSOIL.

Budget mufflers. What do you get for $40? How do they sound and how much power do they kill? On this episode of Engine Masters presented by AMSOIL, we run our 408 Cleveland with 12 different muffler options, including no muffler, straight through, chambered, and turbo style. Which one is best for you is up to you, but here’s all the info you’ll need to make the decision.

This time, the comparison features 100-percent more hydraulic cam! Last round we compared hydraulic and solid roller lifters on hydraulic and solid cams, respectively. But we have more questions! For instance, can you actually run solid roller lifters on a hydraulic cam? Why would you? And, if you do, will they make more power? How long will they survive? The list goes on, but check out the answers for yourself on this episode of Engine Masters presented by AMSOIL, and hopefully you’ll be as intrigued as the rest of us.

How much effort have you put into tuning your carb and ignition? We’re always talking about ignition timing and air/fuel ratios, but never about their direct impact on your power production. This time on Engine Masters presented by AMSOIL, we show you how much power you could be throwing away with a subpar tune-up.

On this episode of Engine Masters presented by AMSOIL, David Freiburger and Steve Dulcich welcome back Richard Holdener to blow the literal lid off of internet “blower manifold” theories. You’ve seen us play with runner lengths before, but this time we use FAST’s modular-runner intake manifold to test both short and long runners to see how each reacts in both NA and boosted trim. Is there such thing as a “blower manifold” or is it all just keyboard huff and puff? Join us to find out, won’t you?

On this episode of Engine Masters presented by AMSOIL, David Freiburger, Steve Dulcich, and special guest Richard Holdener explore the science of reducing temperature out of a turbo in order to increase power out of the engine. Intercoolers cool wonderfully, but they can be expensive and tough to package. Water/meth injection is cheaper and easier to package, but will it cost you power in the end?

On this episode of Engine Masters presented by AMSOIL, we take the mystery out of carburetor selection. More air means more power, but is there such a thing as too big? And how do you know when you’ve passed good? David Freiburger, Steve Dulcich, Steve Brulé from Westech Performance, and the dyno get together to compare carbs from 650 to 950 cfm on Our Ultimate Average 383 to help you find all the power and all the driveability.

This time on Engine Masters presented by Amsoil, we explore what we’ve always known: Increased engine temperature decreases power output. We always thought we knew the answer, but today our 598 Chevy big-block gets some special heat treatment to find out exactly how and why heat kills power. The answer might be just as surprising to you as it was to us.

This time on Engine Masters presented by Amsoil, we go head-to-head-to-head-to-head to find the best dual-plane for your buck. Using our longtime test mule 372 small-block Chevy, we bolt up the four most popular Air-Gap–style dual-planes to compare power and cost, to help you make the best choice for your engine and budget.

A junkyard Chevy LS engine with a turbo—it’s a dime-a-dozen concept these days, but how big can it go? To find out, Engine Masters went to the originator of the “Big Bang Theory” dyno test: Richard Holdener, who delivered the world a 1,200hp boosted 4.8L way back in 2011 in the pages of HOT ROD magazine. Holdener has brought many junkyard engines to a power-adder-assisted demise since then, and has found the connecting rods to be the weak spot. The Gen IV engines have better rods, so this time the victim is a 6.0L with a pair of BorgWarners on the way to 30 psi. Will it go or will it blow? Find out in jaw-dropping fashion on this episode of Engine Masters presented by AMSOIL.

Get ready for “no replacement for displacement” with a massive 598ci BluePrint Engines crate big-block Chevy! On this episode of Engine Masters presented by AMSOIL, we’re going to show you two completely different power combos, one for low-buck and massive street-ready low-end torque, and a second one for high-buck and high-rpm killer horsepower. Both of these setups proved super effective and we’d encourage you to duplicate them, but the episode also addresses the age-old questions about torque versus horsepower and how they are affected by parts selection and rpm—as well as how they might need to be set up in a car. And by the way, we LOVE this engine!

You asked and we're here to answer! On this episode of Engine Masters presented by AMSOIL, we take our small-block Chevy 383 and show, piece by piece, how much power your water pump kills. We move from an electric pump to mechanical with all kinds of cooling tricks to show you just how little it matters. We even throw on an alternator under load just to drive the point home. Engine Masters is supported by Summit Racing Equipment, Holley/MSD, Earls Vapor Guard Hose, and Mr. Gasket.

There is no hotter engine package these days than the turbocharged GM LS-Series V-8. Many people have proven that you can pull a 4.8L or 5.3L straight out of a junkyard and boost it to the moon and make 1,000 hp—but what if you’re a little more conservative and want to have huge power but also reliability from an engine you can drive every day on pump gas? That’s what you’ll learn about on this episode of Engine Masters presented by AMSOIL. We’ll show you where we spent the money and where we saved it, and why we chose some lower-power components in favor of budget and reliability as we make incredible power from a 5.3L with a single turbo, 91-octane fuel, and stock cylinder heads.

It’s back to basics this time on this episode of Engine Masters presented by AMSOIL, with a comparison of dual-plane versus single-plane intake manifolds. While the intakes used here are typical for any carbureted V-8, the lessons about how the length of the intake runners affects the shape of the power curve apply to any four-stroke engine. So are you into low-end grunt, or top-rpm horsepower? And how much of one are you willing to sacrifice to get the other? This episode will help you answer those questions. Engine Masters is supported by MSD, Holley, Permatex, Auto Meter, and Summit Racing!

On this episode of Engine Masters presented by AMSOIL, we explain how oil kills power—because it’s not about synthetic versus regular oil and not about a brand-to-brand comparison, but about windage and oil-pan design. We take a 700hp big-block Chevy and show you how too much oil can kill 20 hp, and you’ll also see gains when we go from a stock-design pan to a Milodon drag-racing oil pan. We are thankful for Engine Masters’ sponsors Permatex (for no oil leaks!), Auto Meter (to check oil pressure), Mr. Gasket (to keep the oil inside), Earls (for AN oil lines and more), and Summit Racing Equipment (where you can buy it all).

This time on Engine Masters presented by AMSOIL, it’s a horsepower battle with the world’s most popular classic V-8s: the Chevy small-block versus the Ford Windsor. Using rebuilt short-blocks and parts packages from SummitRacing.com, the Engine Masters team built two engines as equally as possible, using a Chevy 350 and a Ford 351 with Holley carburetors, Edelbrock RPM Air Gap intakes, Air Flow Research 195 heads, Comp Cams hydraulic roller cams, and 13/4-inch-tube headers. Will one small-block make more power than the other based on inherent design superiority? The dyno is here to find out. Engine Masters is supported by Mr. Gasket, Earl’s Vapor Guard, Auto Meter, Summit Racing, and Permatex.

On this episode of Engine Masters presented by AMSOIL, we test the power differences between 118-octane race gas and Rockett Brand E85 ethanol-blended fuel. There’s a lot more to just the horsepower curve, though, as we test Holley’s out-of-the-box carburetor tunes, discuss other tuning differences, and go over a long list of other considerations you should make if you’re planning a changeover to E85. While the ethanol blend can be used for a variety of different engine designs, the test here focuses on a naturally aspirated, high-compression engine making 750 horsepower. Can you drive an engine like this on the street with E85 and save money on fuel? Find out on this episode of Engine Masters, which is supported by Earl’s Vapor Guard hose (specifically made to endure ethanol fuels), Mr. Gasket, Auto Meter, Permatex, and Summit Racing.

There’s nothing we love more for big torque and visual impact that a good ol’ antiquated roots supercharger! This time on Engine Masters, presented by AMSOIL, hosts David Freiburger, Steve Dulcich, and Steve Brulé show you how to install and tune a Weiand 6-71 blower and dual 750-cfm double pumpers on a budget 350ci Chevy short-block. Engine Masters is supported by Earl’s Vapor Guard hose, Mr. Gasket, Auto Meter, and Permatex.

On this episode of Engine Masters presented by AMSOIL, we explore an ancient scenario but still one of the most-asked tech questions we are asked: What budget bolt-ons can be used on a stock small-block Chevy 5.7 to get more horsepower? Watch as we take the cheapest Chevy 350 crate engine you can buy and make mods that gain nearly 130 horsepower! It’s a dyno-proven, easy-to-install power combo that will give you the best bang for your buck.

This episode of Engine Masters presented by AMSOIL we take the Roadkill Rotsun and find out how much power that bone stock turbo charged 1987 5.0L Mustang engine really makes. With a science experiment of a rig, get ready to be shocked! The numbers don’t lie. Engine Masters is supported by Autometer, Mr. Gasket, Earl’s Vapor Guard, and Permatex!

This episode of Engine Masters presented by AMSOIL delivers the goods many viewers have asked for as we test the power of straight dual exhaust with no crossover pipe versus using an H-pipe versus an X-pipe. Will the old bench-racing stories come true, or is it all hocus-pocus? We find out using a basic 5.3L GM LS3 engine then precisely spell out the effect these exhaust-system modifications have on horsepower and torque. Engine Masters is supported by Mr. Gasket, Earl’s Vapor Guard hose, and now Permatex!

This episode of Engine Masters presented by AMSOIL reinforces the fact that Steve Dulcich is not just the guy in the back of the dyno room—he’s a legit engine master. And you won’t question that after you see his homegrown porting job on a set of Edelbrock aluminum cylinder heads for a small-block Mopar pick up a whopping 92 hp! To be fair, that gain also includes porting work on the Victor Jr. intake manifold by Bryce Mulvey. All this work tops off the same 410ci small-block Mopar from BluePrint Engines that was seen on Engine Masters Episodes 11 and 18. Engine Masters is supported by Mr. Gasket and Earl's Vapor Guard.

Usually on this show, we are all about making more horsepower, but on this episode of Engine Masters presented by Amsoil, we are trying to kill horsepower! We bolt four different types of cooling fans onto our 350 small-block Chevy, all with different designs and material. Which one takes the most horsepower, and which one takes the least? Watch and find out!

Ever wonder what those camshaft specification numbers really mean and how they affect engine performance? This episode of Engine Masters presented by AMSOIL is here to help, as David Freiburger explains cam lift, duration, love separation angle, and installed centerline. Next, we test a low-rpm cam and a high-rpm cam in the same engine to demonstrate the power differences. Engine Masters is supported by Mr. Gasket and Earl's Vapor Guard hose.

We show you why the age-old concept of pulling a used engine from a running car and slapping some speed parts on itmight not always be the best idea. Our special guest engine is the Mopar 360 small-block V8 from Episodes 3 and 4 of Roadkill Garage, where we plucked it from a 1975 Dodge truck and slapped it into a 1970 Dodge Challenger. For this show, we set up the 360 with all-stock parts, ran it on the dyno for a baseline, and then added a bunch of speed parts. We gained 140 horsepower.

The 13th episode of Engine Masters, presented by AMSOIL, is an unlucky one for a poor little 305ci Chevy small-block. It was the victim of our test of how much nitrous oxide power boost can be tolerated by a completely stock short-block with the original cast crank, rods, and pistons.

In episode 4 we famously destroyed a set of Hooker headers with a hammer to see if dents in tubes really make a difference in performance. Folks said our test was flawed because if dents in the tubes didn't affect performance, then the headers must have been too large to begin with. So now we've tested that theory, running three sets of Hookers on the same engine we used in the header-bash episode. We tried 1-5/8, 1-3/4, and 1-7/8. Were the viewers right that we'd picked wrong the first time?

The 408 is one of the most popular small-block V-8 stroker combinations for Chevy, Ford, and Mopar.

In this episode of Engine Masters presented by AMSOIL, you'll learn a simple combination for a 600hp big-block Chevy.

You're sitting around with your typical street/strip V-8 and wondering, should I get 2.5-inch-diameter exhaust pipes and mufflers, or should I go 3-inch? In this episode of Engine Masters, presented by AMSOIL, we will help you decide.

Boost is good. Forced induction makes huge power, and you want it cheap and easy. This time on Engine Masters presented by AMSOIL, we look at the two most affordable implements of boost from SummitRacing.com.

Dual quads! Three deuces! Eight barrels! Six jugs! The lore of multiple carburetors runs deep in the hot rodding world, and in the muscle car era it was common for the OE manufacturers to up their cars' performance

Topping your engine with a set of aftermarket cylinder heads is a near-certain method for making more horsepower and torque-but is the extra power really worth the money? In this episode of Engine Masters, presented by Amsoil, we answer that question.

This time on Engine Masters, presented by Amsoil, you'll learn a good combo for 470-plus horsepower from a stock-bottom-end 5.7L Dodge Hemi, and then see us add a Paxton supercharger in the hunt for 707 horsepower just like one of the new Dodge Hellcats.

If you've ever installed a set of high-performance exhaust headers, then you've probably bashed those exhaust tubes with a hammer to get them to clear everything in the chassis of the car.

It's our first head-to-head shootout with two engines: a Blueprint Engines crate Chevy 383 small-block versus a hand-built Mopar 383 by Engine Masters host Steve Dulcich. To make this a fair test, we equalized as many variables as possible

Should you run a carburetor, or should you try the new and easy self-learning EFI setups? We'll dish up answers in this episode of Engine Masters, presented by AMSOIL. Host David Freiburger, Steve Dulcich, and Steve Brule strap a 5.3L LM7 engine to the engine dyno and look at the price, installation, and power of a Holley 750-cfm double-pumper versus Holley's Terminator throttle-body EFI. The guys come up with a big part-mismatch nightmare along the way-one you should also watch out for. As you're watching the episode, keep in mind that most of the carb-vs-throttle-body info applies to any engine, not just the LS-style test mule. However, Holley does provide very simple, plug-in kits to power the LS platform. In fact, if you have a complete junkyard LS that still has the intake manifold, throttle body, and injectors, you can get a much cheaper LS controller that plugs right in.

In this first episode you'll find out if Blueprint Engines is accurate in its advertised power for a 400ci Chevy small-block crate engine, and then we'll see if Freiburger is justified in his love for dual carburetors and high-rise tunnel-ram intake manifolds-plus there's cash on the line.